Create a New Lawn with Artificial Grass Installation in Dallas

Do you wish to install an attractive artificial Grass lawn that uses fewer resources and costs less? Are you curious about how to do it yourself? In this article, you’ll find out details about Artificial Grass Installation.

Many residential and business yards are going green with synthetic turf due to its cheap maintenance expenses. You don’t have to water or mow synthetic grass, so the lower rates and maintenance requirements are appealing. Read our article below to discover how to install artificial grass like a professional. You’ll learn how to make your yard eco-friendly while still saving money. We offer everything you need to finish your job.

Artificial Grass Installation Dallas TX

How to install artificial grass on soil

To install artificial grass on the soil surface, first remove existing grass and weeds. Level the area and compact the soil. Install a weed mat and a layer of compacted gravel or sand for drainage purposes. Compact it thoroughly. Untwist and cut the blades of the fake grass with scissors up to the marked lines. Place and pin down the edges.

Steps to install artificial grass

In this paragraph, we will discuss the important step of Artificial Grass Installation. So read this part of the article attentively.

1.Step: Excavation

Remove the current lawn and excavate 75mm below the desired finishing height. In some gardens, depending on the existing levels, you can simply remove the existing grass, which will remove approximately 30-40mm, and then build up 75mm from there. A turf cutter, which can be rented from your local tool rental store, will make this procedure much easier.

Step 2: Install trimming.

If there is no existing solid edge or wall surrounding your lawn’s boundaries, you will need to install some type of retaining edge. You can do this with treated timber, steel edging, plastic wood, timber sleepers, or brick/block paving. We suggest employing treated timber edging where possible because it is ideal for fixing grass too. Timber edging should be screwed to wooden stakes hammered into the soil with a club hammer or sled.

Step 3: Install Weed Membrane.

over prevent weeds from sprouting through your lawn, apply weed membrane over the entire area, overlapping the edges to guarantee weeds do not infiltrate between two sections. You can use galvanized U-pins to secure the membrane. If your current lawn or garden is prone to weeds, we suggest spraying the area with weedkiller before.

Step 4: Install the 50mm sub-base and edging.

You can use MOT Type 1 as the sub-base, or if your garden has poor drainage, we propose 10-12mm granite chippings. Rake and level the aggregate to a depth of around 50 mm. It is critical to fully compact the sub-base using a vibrating plate compactor, which can also be rented from a local tool rental store.

Step 5: Install 25mm Laying Course

Granite Dust Laying Course

Rake and level about 25mm of stone dust right on top of the sub-base. If using timber edging, the laying course should be leveled to the top of the timber. Before proceeding, we advise sprinkling the granite dust with water to keep it down; this additionally helps the pieces of stone adhere together.

Step 6: Install an additional weed membrane.

Weed Membrane

We recommend adding a layer of weed barrier just before laying the grass, not only for added weed protection but also to protect the underside of your Neo Grass. As with the first layer of the weed barrier, overlap the edges to prevent weeds from passing between two sections. Pin the membrane to the edge or as close as possible, then remove any excess. It is critical to lay the membrane flat because any ripples will be evident through your artificial grass.

Step 7: Unroll Your Neo Grass Artificial Lawn

You’ll probably need some assistance at this step because, depending on the size of your artificial grass, it can be heavy. If feasible, position the grass so that the pile orientation faces your house or main perspective, as this is usually the best angle to watch the grass from. If you have two rolls of grass, make sure the pile direction is the same in both sections. Before cutting your Artificial Grass, make sure there are no ripples in the grass, and give it a few hours to acclimatize.

Step 8: Cut to size.

Now, using a sharp knife, cut the grass to the desired form, carefully following the border edge to create a snug fit. Blades can blunt rather fast, so keep plenty of spares on hand. If using timber edging, secure the boundary perimeter with galvanized nails; for steel, brick, or sleeper edging, use galvanized U-pins.

Step 9: Secure any joints.

If done correctly, the joints should not be apparent. First, align both pieces of grass such that the pile direction is the same and they run parallel to each other. Fold back both sections of grass by approximately 300mm to show the latex backing. Cut off three stitches from each patch of grass, being careful to cut in a straight line. Then, lay each piece flat again to ensure that the edges of the two pieces of grass touch. There should be a constant 1-2mm gap. When both sections are appropriately positioned, fold the grass back over to reveal the latex backing.

Next, place the connecting tape (shiny side down) between the two pieces of grass and apply the glue. Carefully reposition each piece of grass, ensuring that the grass fibers do not come into contact with the glue or become buried. Walking gently along the connection will guarantee proper contact between the grass and the adhesive. Finally, give the glue enough time to cure.

Step 10: Groom your new lawn.

Finally, apply kiln-dried sand to your lawn to help it settle and last longer. This process can only be done when the grass is entirely dry; otherwise, the sand will clump together. If possible, use ‘weed-free’ kiln-dried sand, which is available at major DIY hardware stores. We recommend using 5 kg per square meter.

Then, using a stiff broom or power brush (we strongly recommend a power brush for optimum results!), brush your lawn in the opposite direction of the pile height to incorporate the sand and assist elevate the fibers into an upright position. Finally, pour yourself a drink and appreciate your new prize-winning lawn!

If you are installing fake grass on concrete, please refer to our step-by-step guide.

How to Install Artificial Grass.

To keep things simple, you can lay artificial grass using the necessary materials stated above and following our six simple procedures below:

1. Prepare and clear the space.

2. Build an edge.

3. Lay the basis.

4. Apply the weed membrane.

5. Install the artificial grass and trim the edges.

6. Add final touches.

Post-Installation Maintenance and Care of artificial Grass

1. Regular cleaning and brushing.

Clear away the debris.

Clear any debris from your fake grass regularly, especially after a rain or windy day. Leaves, branches, and other debris have their visual appeal and performance.

This activity can be easily accomplished by hand-picking larger materials.

Rinse the lawn.

To eliminate dust, pollen, and loose dirt from your artificial grass, rinse it regularly with water. Depending on your region and the frequency of rain, you may need to rinse the grass more or less often.

Brushing for a natural appearance.

Brushing up the grass fibers (against the grain) regularly helps to keep your lawn upright, resulting in a lush and bright appearance. To complete this operation, use a stiff-bristle broom or a specialized turf brush.

Remove stains soon.

Spillages can be cleaned away using water. For lightly contaminated areas, a basic solution of warm water and a tiny bit of mild detergent is sufficient. Wipe it with a sponge and then rinse.

Managing pet waste

 a. Dealing with Pet Urine

You do not need to wipe the lawn after each urination. It is recommended to hose down the turf once a week, especially if it hasn’t rained, to remove any residue.

b. cleaning pet excrement.

Cleaning up pet feces in turf is similar to caring for natural grass. Allow the waste to dry slightly to avoid spreading, and then use a doggie bag or scooper for solid waste. If you have diarrhea, use a bag or paper towels to remove as much as you can.

Repairing damaged Artificial Grass Installation sections

(a). DIY Repairs for Small Areas

For modest repairs, replacing the damaged patch may be a straightforward DIY project. It is typically ideal to keep any leftover turf from the initial installation for repairs to ensure the finest color match.

Trim the damaged turf and install the replacement piece in its original location, aligning the fibers with those of the current turf. Secure the turf with nails and a hammer, then add filler to improve consistency and beauty.

b. Professional assistance for larger areas.

For more serious damage, professional turf installers may be required to provide a seamless repair.

How to install artificial grass over a concrete patio

To install the artificial on the concrete surface, it is essential to ensure that the surface of the concrete is clean. Place the shock-resistant foam layer to absorb shock and assist drainage. Fit the artificial grass and cut any excess to leave the foam layer of at least about two inches encircling the area for fitting the grass. Apply the grass using outdoor glue, ensuring that the edges and seams receive some glue, and then uniformly place the grass. Grass fibers are pet-friendly and will be brushed upwards.

How do they install artificial grass in the cheapest way possible?

The simplest cost-effective method of laying down artificial grass will be to prepare the area yourself by digging out the existing grass and leveling the ground. Choose cheaper alternative artificial grass and do away with thick underlays. In place of the base, opt for sand or cyclonic gravel that has been compacted. Use landscape pins to attach the grass instead of glue, and install the grass by yourself to sidestep hiring experts.

What is the price for artificial Grass Installation provided by Home Depot?

Home Depot installs synthetic grass at a cost that is charged per square foot of area. The installation fee is charged between $5.50 and $18.75. It varies by the area of the grass, the kind of turf, etc. An average estimate per installation of these systems is about $5000. Nevertheless, in these cases, the possible costs are for the provision of site preparation, any additional landscaping, that is removal of debris, and also the installation of a drainage system if required. Smaller yards usually cost a higher price per square foot in comparison to larger yards. While Home Depot provides complimentary estimates and consultation skills for installations, the availability of offers may differ by location.

How to lay artificial grass on sand

To lay artificial grass on sand first remove all weeds and compact the soil in the area where the grass will be installed. First, apply a layer of sharp sand of approximately 40-50mm thick and level the surface. Move the sand over to achieve a level surface that is reasonably solid and smooth. Using sand as the layer on which the artificial grass is built, lay the grass in a way that all grass fits within the target area. Hold the edges down using landscaping pins and brush the grasses.